AOC E936VW - Betriebsanweisung

AOC MONITOR USER`S GUIDE e936Vw SAFETY INTRODUCTION…………………………………………………………….2 SETUP…………………………………………………………………………………….5 ADJUSTING…………….…………………………………………

4.Ckick on the “Change display settings” button. 5.Click the “Advanced Settings” button. 6.Click the “Monitor” tab and then click the “P

7.Click the “Driver” tab. 8.Open the "Update Driver Software-Generic PnP Monitor" window by clicking on “Update Driver... “and then

9.Select "Let me pick from a list of device drivers on my computer". 10.Click the “Have Disk” button. Click on the “Browse” button an

14.Restart the system. The system will automatically select the maximum refresh rate and corresponding Color Matching Profiles. For Windows Vista

6 Set the resolution SLIDE-BAR to 1366x768 . For Windows XP: 1 Click START. 2 Click SETTINGS. 3 Click CONTROL PANEL. 4 Click Appearance and

5 Double click DISPLAY. 6 Click SETTINGS. 7 Set the resolution SLIDE-BAR to 1366x768 . For Windows ME/2000: 1 Click START. 2 Click SETTINGS.

The recommended resolution for this monitor is 1366 by 768. To setup the monitor to this resolution, follow the steps below. For Windows Vista: 1 Clic

6 Set the resolution SLIDE-BAR to 1366 by 768. For Windows XP: 1 Click START. 2 Click SETTINGS. 3 Click CONTROL PANEL. 4 Click Appearance an

5 Double click DISPLAY. 6 Click SETTINGS. 7 Set the resolution SLIDE-BAR to 1366 by 768. For Windows ME/2000: 1 Click START. 2 Click SETTINGS.

Power Press to turn on or turn off the monitor. 4:3 or wide / Up Press key to change the screen aspect ratio between sta

SAFETY INTRODUCTION The following subsections describe notational conventions used in this document. Notes, Cautions, and Warnings Throughout this gu

Eco mode ---DCR, Standard, Text, Internet, Game, Movie, Sports DCR Standard

TEXT INTERNET Game

Movie Sports Notes : When Eco mode is not set as “Standard”, Contrast and Brightness can not be adjusted; When DCR is set as “On”, Contrast, Bri

LED INDICATOR Status LED Color Full Power Mode Blue Active-off Mode Orange

DRIVER INSTALLATION GUIDE Windows 2000 1. Start Windows® 2000 2. Click on the 'Start' button, point to 'Settings', and then click

4. Click on the 'Display' Item. 5. Select the 'Settings' tab then click on the 'Advanced' button. 6. Selec

7. Click on the 'Driver' tab and then click on 'Update Driver...' button. 8. Select the 'Install from a list or speci

9. Select the 'Don't Search. I will choose the driver to install' radio button. Then click on the 'Next' button. 10. Cl

2. Click "Personalization" and then "Display Settings". 3. Click "Advanced Settings...". 4. Click "Proper

5. Click "Update Driver..." in the "Driver" tab. 6. Check the "Browse my computer for driver software" checkbox a

See below the recommended ventilation areas around the monitor when the monitor is installed on the wall or on the stand:

8. Select your monitor model and click on the 'Next' button. 9. Click "Close" → "Close" → "OK" → "OK"

TROUBLESHOOT Problem & Question Possible Solutions Power LED Is Not ON • Make sure the power button is ON and the Power Cord is properly connect

Picture has color defects (white does not look white) • Adjust RGB color or select desired color temperature. Horizontal or vertical disturbances on

Clean the cabinet regularly with the cloth provided. You can use soft-detergent to wipe out the stain, instead of strong-detergent which will caute

SETUP Please setup or remove the base following the steps as below. Setup:

Remove:

• For optimal viewing it is recommended to look at the full face of the monitor, then adjust the monitor's angle to your own preference. • Hol

To protect equipment, always turn off the PC and LCD monitor before connecting. 1. Connect the power cable to the AC port on the back of the monitor

Adjusting The recommended resolution for this monitor is 1366x768 . To setup the monitor to this resolution, follow the steps below. For Windows 7: 1